So when [GreatScott] rebuilt his recent DIY coil gun with discrete logic, mechanism for a small coil gun, and as such he chose an Arduino to. How to Make a Coilgun. When you hear the word coilgun, you might imagine a futuristic weapon that shoots electricity or coils, but these experimental devices. A coil-gun uses a magnetic field to accelerate a bullet up to projectile speed. Jason’s uses a bank of recycled rechargeable laptop batteries to.

Author: Shakagor Sakasa
Country: Tajikistan
Language: English (Spanish)
Genre: Politics
Published (Last): 10 July 2006
Pages: 493
PDF File Size: 15.36 Mb
ePub File Size: 3.62 Mb
ISBN: 728-4-44195-690-7
Downloads: 68619
Price: Free* [*Free Regsitration Required]
Uploader: Gale

DIY coilgun gives clever hobbyists the risk of permanent injury

Tips If the coil doesn’t stay, try something to retain it, like steel washers, or hot glue. Place a fresh set of batteries into the battery holder and turn the voltage potentiometer R11 all the way counter-clockwise and then turn on the main power switch. The completed accelerator coil, barrel, and breech loading mechanism are shown in Figure Analog electronics are generally going to last a lot longer than a cheap chinese arduino clone.

Death or Serious Injury May Occur. EM Coil Gun Website www. It might be interesting to find out how many people adopted that style because it made their handwriting more readable. Leave a Reply Cancel reply Enter your comment here Hilarious Science How To: When fire switch S3 is closed, voltage is applied to the gate of the SCR, switching it on and dumping the charge across the capacitor bank into the accelerator coil L1. Upload a picture for other readers to see.


The video points out the only real reason for using discreet logic or an FPGA, and that is when the microcontroller cannot handle the speed requirement.

How To Make A Coil Gun: Turning Electricity Into Velocity « Fear Of Lightning :: WonderHowTo

Use two plastic or cardboard riy glued to each end of the barrel on both sides of the coil to add support. You can use any sort of light plastic or nylon tubing material that can be obtained at most hobby shops. This isn’t a weapon. A suggested metal cutting and drilling template is shown in Figure 6.

This guy loves to teach. Caution Coklgun information contained in this article is dangerous and potentially life threatening. Now, insert the magnetic projectile in the one inch end of the coil, or the back end. So when [GreatScott] rebuilt his recent DIY coil gun with discrete logicwe just had to get the word out.

Always wear eye protection. Skip to main content.

You will need to experiment with the initial position of the projectile to achieve the highest velocities. If the gun is not fired immediately after fully charging, the voltage level on the capacitor bank will slowly start to decrease due to leakage and the comparator will turn the charging circuit back on to keep the capacitor bank voltage level topped off.


Notify me of new comments via email. Or he could coilgunn used a and saved a whole bunch of other components as well, seeing the chip is well capable of driving the FETs directly.

Video: DIY Coilgun Turns Voltage into Kilojoule Projectile Power

The basic control circuit was simple, but too simple for safety — a projectile stuck in the barrel could leave a coil energized indefinitely, leading to damage.

Aluminum covers and side panels.

What is the ID and the OD of the preferred tube size? By using this service, some information may be shared coilfun YouTube. To create this article, 22 people, some anonymous, worked to edit and improve it over time. Attach the other end of one of these wires to one end of the coil’s wires.

Dr. Monk’s DIY Electronics Blog: DIY Coilgun

Also in Italy we write in this way the 7s. The doubler cascade is sometimes also referred to as the Greinacher multiplier.

Thanks for letting us know. Coil gun systems www. If the circuit was analog, you could trace how it works and fix the part that is broken.